Nomad Wings Extreme

Product Overview


The Nomad Wings Extreme is a high-performance 5G, 2X2 MIMO cellular, omni-directional antenna designed for enterprise environments, both indoors and outdoors 🌐. It delivers 2X data speeds across the full 600 MHz to 6 GHz 5G spectrum, making it ideal for boosting cellular coverage in retail, office, or outdoor spaces🏒🌲. With its minimalist design and small footprint, the Nomad Wings Extreme offers high-capacity throughput with a discreet aesthetic.

The IP54-rated antenna can be wall or pole mounted πŸ› οΈ and comes with low-loss cables to ensure maximum performance and router optimization πŸ“ˆ.


🧰 Required Tools

  • Phillips Screwdriver

  • 5/16” Torque Wrench (5 in.-lb)

  • 7/32” Drill Bit

  • 7/16” Wrench

  • Loctite or 3M Red 271 Thread Locker


βš™οΈ Mounting Options

πŸ”Έ Wall Mount: Suitable for indoor installations 🏠. Use the provided mounting bracket and screws to secure the antenna to a non-metallic wall.

πŸ”Έ Pole Mount: For outdoor or pole installations, mount the antenna to a vertical pole with a diameter between 1.5 inches and 2.5 inches using the provided V-bolt, saddle clamp, and hardware πŸ—οΈ.


πŸ“ Placement Considerations

πŸ“ Omni-Directional: Ensure the antenna is mounted properly to maximize the 360-degree horizontal coverage.


⚑ Interference: Keep the antenna at least 24 inches away from electrical devices like lights, routers, and AC units to avoid signal interference.


🧱 Signal Path Loss: Avoid obstructions such as concrete walls or metal objects that may absorb or reflect the signal.


πŸ”Œ Cable Length: Use the shortest possible cables to reduce signal loss. Avoid bending the cables sharply.


πŸ”§ Installation Steps

Pole Mount:

  1. Choose a location with a clear line of sight to the nearest cellular towerπŸ“Ά.

  2. Attach the mounting bracket to the back of the antenna using the four thread-forming screws.

  3. Mount the antenna to the pole using the provided V-bolt and hardware. Tighten the nuts with the 7/16" wrench, ensuring the antenna is securely fastened πŸ”©.


Wall Mount:

  1. Use a stud finder to select a stable location. Drill two 7/32" holes into the wall, ensuring the area is free of metal obstructions πŸ› οΈ.

  2. Attach the mounting bracket to the antenna and fasten it to the wall with the provided screws πŸ”§.


Cable Routing:

  1. Route the antenna cables to the router, ensuring no sharp bends. Secure the cables approximately 6 inches below the antenna using UV-resistant cable ties for outdoor setups 🌞.

  2. Waterproof the RF connectors using electrical tape or heat-shrink tubing for outdoor installations πŸ’§.


Cable Connection Instructions

  1. Clean the connectors using canned air or isopropyl alcohol to remove any dust 🧼.

  2. Connect the antenna cables to the designated terminals on the router:

    • CELL 1 to MAIN0

    • CELL 2 to AUX0/DIV


πŸ”Commissioning & Testing

  • Confirm that all coaxial cable connectors are secure and that there are no sharp bends in the cables πŸ”„.

  • Use a cellular device’s built-in diagnostics to verify an RSSI signal strength higher than -75dB πŸ“Š.

  • Ensure the cellular connection supports the required data rates for optimal performanceπŸš€.

⚠️ Safety Warnings

  • Maintain a minimum separation of 20 cm from the antenna to comply with RF exposure requirements πŸ“.


  • Avoid installing the antenna in windy conditions or near power lines to prevent serious injury 🌬️⚑.


πŸ“ž For further inquiries or support, contact Nomad Internet Support at support@nomadinternet.com βœ‰οΈ.